Ultra Low loss flexible 50 ohms RF 5012S coaxial cable
| Construction | |||
| inner conductor | material | Copper clad aluminum wire | |
| dia. | 3.55±0.04 mm | ||
| insulation | material | physically foamed PE | |
| dia. | 9.20±0.20 mm | ||
| outer conductor | material | Helical corrugated copper | |
| diameter | 12.00±0.20 mm | ||
| jacket | material | PVC or fire retardant PE | |
| diameter | 13.60±0.20 mm | ||
| mechanical properties | |||
| bending radius | single repeated moving |
25 mm 30 mm 200 mm |
|
| pulling strength | 800 N | ||
| crush resistance | 1.9 kg/mm | ||
| recommended temperature | PE jacket | store | -70±85°C |
| installation | -40±60°C | ||
| operation | -55±85°C | ||
| fire retardant PE jacket | store | -30±80°C | |
| installation | -25±60°C | ||
| operation | -30±80°C | ||
| electrical properties | |||
| impedance | 50±2 Ω | ||
| capacitance | 82 pF/m | ||
| inductance | 0.205 uH/m | ||
| propagation velocity | 81 | ||
| DC breakdown voltage | 2.5 | ||
| insulation resistance | >5000 | ||
| peak power | 15.6 | ||
| screening attenuation | >120 | ||
| cut-off frequency | 10.2 | ||
| attenuation and average power | |||
| frequency,MHz | power rate@20°C,kW | nom.attenuation@20°C,dB/100m | |
| 10 | 10.1 | 1.04 | |
| 100 | 3.08 | 3.41 | |
| 450 | 1.38 | 7.59 | |
| 690 | 1.158 | 9.58 | |
| 800 | 1.01 | 10.40 | |
| 900 | 0.943 | 11.20 | |
| 1000 | 0.889 | 11.80 | |
| 1800 | 0.634 | 16.60 | |
| 2000 | 0.597 | 17.60 | |
| 2200 | 0.566 | 18.61 | |
| 2400 | 0.539 | 19.59 | |
| 2500 | 0.529 | 20.07 | |
| 2600 | 0.518 | 20.55 | |
| 2700 | 0.507 | 21.02 | |
| 3000 | 0.469 | 22.40 | |
| maximum attenuation value may be 105% of the nominal attenuation value. | |||
| vswr | |||
| 820-960MHz | ≤1.15 | ||
| 1700-2200MHz | ≤1.15 | ||
| 2300-2400MHz | ≤1.15 | ||
| standards | |||
| 2011/65/EU | compliant | ||
| IEC61196.1-2005 | compliant | ||
Packing Reference
Installation Instructions of N or 7 / 16 or 4310 1 / 2″ super flexible cable
Structure of connector: ( Fig1 )
A. front nut
B. back nut
C. gasket
Stripping dimensions is as shown by diagram ( Fig2 ), attention should be paid while stripping:
1. The end surface of inner conductor should be chamfered.
2. Remove impurities such as copper scale and burr on the end surface of the cable.
Assembling the sealing part: Screw the sealing part in along the outer conductor of the cable as shown by the diagram ( Fig3).
Assembling the back nut (Fig3).
Combine the front and back nut by screwing as shown by diagram ( Figs( 5)
1. Before screwing, smear a layer of lubricating grease on the o-ring.
2. Keep the back nut and the cable motionless, Screw on main shell body on back shell body. Screw down main shell body of back shell body using monkey wrench. Assembling is finished.
