Low PIM 7/16 DIN Male to 4.3-10 Male Adapter


  • Place of Origin: Shanghai, China (Mainland)
  • Brand Name: Telsto
  • Model Number: TEL-4310M.DINM-AT
  • Type: 4.3-10 to 7/16
  • Application: RF
  • Material: Brass and Teflon
  • Plating: Sliver and Tri-alloy
  • Product name: 4.3-10 male to 7/16 male Connector
  • Inter modulation 3rd: 155dBc
  • VSWR: ≤1.10@DC-3000MHz
  • Impedance: 50ohm
  • Frequency Range: DC-6GHz
  • Weatherproof Rate: IP67
  • HS code: 85369090
  • Description

    Specifications

    Product Support

    Adaptors manufactured by Telsto Development Co., Limited are in a wide range of various configurations like within series or between series, straight or angled design and some with panel mount features.

    They are classified according its typical intended applications of which each require its specific properties. There are four major groups which are identified by means of a color code in this catalogue: standard, precision, low passive inter-modulation(PIM)and quick-mate adaptors.

    Telsto RF Adapter has an operational frequency range of DC-3 GHz, offers excellent VSWR performance and Low Passive Inter modulation {Low PIM3 ≤-155dBc(2×20W)} . This makes it ideally suited for use in cellular base stations, distributed antenna systems (DAS) and small cell applications.

    TEL-4310M.DINM-AT

    Product

    Description Part No.

    RF Adapter

    4.3-10 Female to Din Female Adapter TEL-4310F.DINF-AT
    4.3-10 Female to Din Male Adapter TEL-4310F.DINM-AT
    4.3-10 Female to N Male Adapter TEL-4310F.NM-AT
    4.3-10 Male to Din Female Adapter TEL-4310M.DINF-AT
    4.3-10 Male to Din Male Adapter TEL-4310M.DINM-AT
    4.3-10 Male to N Female Adapter TEL-4310M.NF-AT
    Din Female to Din Male Right Angle Adapter TEL-DINF.DINMA-AT
    N Female to Din Male Adapter TEL-NF.DINM-AT
    N Female to N Female Adapter TEL-NF.NF-AT
    N Male to Din Female Adapter TEL-NM.DINF-AT
    N Male to Din Male Adapter TEL-NM.DINM-AT
    N Male to N Female Adapter TEL-NM.NF-AT
    N Male to N Male Right Angle Adapter TEL-NM.NMA.AT
    N Male to N Male Adapter TEL-NM.NM-AT
    4.3-10 Female to 4.3-10 Male Right Angle Adapter TEL-4310F.4310MA-AT
    DIN Female to Din Male Right Angle RF Adapter TEL-DINF.DINMA-AT
    N Female Right Angle to N Female RF Adapter TEL-NFA.NF-AT
    N Male to 4.3-10 Female Adapter TEL-NM.4310F-AT
    N Male to N Female Right Angle Adapter TEL-NM.NFA-AT

    Related

    Product Detail Drawing01
    Product Detail Drawing02
    Product Detail Drawing03
    Product Detail Drawing04

  • Previous:
  • Next:

  • TEL-4310M.DINM-AT

    Model: TEL-4310M.DINM-AT

    Description

    4.3-10 Male to Din Male Adapter

    Material and Plating
    Center contact Brass / Silver Plating
    Insulator PTFE
    Body & Outer Conductor Brass / alloy plated with tri-alloy
    Gasket Silicon Rubber
    Electrical Characteristics
    Characteristics Impedance 50 Ohm
    Frequency Range DC~3 GHz
    Insulation Resistance ≥5000MΩ
    Dielectric Strength ≥2500 V rms
    Center contact resistance ≤3.0 mΩ
    Outer contact resistance ≤2.0 mΩ
    Insertion Loss             ≤0.3dB@3GHz
    VSWR                    ≤1.1@-3.0GHz
    Temperature range  -40~85℃
    PIM  dBc(2×20W) ≤-160 dBc(2×20W)
    Waterproof IP67

    Installation Instructions of N or 7 / 16 or 4310 1 / 2″ super flexible cable

    Structure of connector: ( Fig1 )
    A. front nut
    B. back nut
    C. gasket

    Installation Instructions001

    Stripping dimensions is as shown by diagram ( Fig2 ), attention should be paid while stripping:
    1. The end surface of inner conductor should be chamfered.
    2. Remove impurities such as copper scale and burr on the end surface of the cable.

    Installation Instructions002

    Assembling the sealing part: Screw the sealing part in  along the outer conductor of the cable as shown by the diagram ( Fig3).

    Installation Instructions003

    Assembling the back nut  (Fig3).

    Installation Instructions004

    Combine the front and back nut by screwing as shown by diagram ( Figs( 5)
    1. Before screwing, smear a layer of lubricating grease on the o-ring.
    2. Keep the back nut and the cable motionless, Screw on main shell body on back shell body. Screw down main shell body of back shell body using monkey wrench. Assembling is finished.

    Installation Instructions005

  • Write your message here and send it to us